76.00 zł (tax incl.)
Solar set solar collector 1 x WEBER SOL ECO 2.85 without storage tank
Intended use: Solar set intended for single-family buildings with a daily consumption of hot water not exceeding 150 liters, which usually corresponds to a family of 3.
POLAND PRODUCT
Solar set with WEBER SOL ECO 2.85 solar collector - without hot water storage tank.
SOLAR KEYMARK certificate - none
If you want to take advantage of subsidy programs - choose collectors or sets in STANDARD OR PREMIUM version
GENERAL INFORMATION
High-quality solar set with 1 solar collector of WEBER SOL ECO 2.85 brand. The set does not include a hot water storage tank.
Adopted collector area provides efficient heating of water at about 40% of annual demand. The remaining 60% (winter period) should be provided using central heating boilers, which are connected to the upper coil of the storage tank or by means of an electric heater.
COMPONENTS
1 x WEBER SOL ECO 2.85 solar collector
1 x solar controller WEBER CONTROL CLASSIC PWM
1 x electronic solar pump group HYDRA GPS PWM with rotameter
1 x cable and rack for mounting the diaphragm vessel
1 x valve for disconnecting the diaphragm vessel without draining the system of liquid
1 x solar diaphragm vessel (expansion tank) 18 l.
1 x set of connectors for connecting the collectors
1 x connection with manual air vent and immersion scabbard for temperature sensor
1 x solar installation fluid (propylene glycol) or 20 l of ready mix depending on availability
MAIN ADVANTAGES
Negligible cost of use
Fully maintenance-free
Long service life
Polish product
TECHNICAL PARAMETERS OF THE MAIN COMPONENTS
WEBER SOL ECO 2.85 solar collector
Warranty: 10 years
Factory service
Total area (gross): 2,85 m2
Absorber area: 2,6 m2
Dimensions: 127 x 224 x 6 cm
Absorption: 95 %
Emission: 5 %
Optical efficiency: > 80 %
Housing/frame: Frame made from a single section with no unnecessary corner joints. Additional protection is polyester coating for very long life. Dark gray color.
Absorber type: Highly selective TINOX / SUNSELECT / BLUETEC.
Absorber arrangement: Single harp (4 spigots)
Absorber tubes: Copper
Connections: 4 x ø18x1 mm
Glazing: 4 mm thick tempered solar glass with low iron oxide content
Insulation: mineral wool
WEBER CONTROL CLASSIC PWM controller.
Large liquid crystal display
Intuitive menu
Pump operation control with PWM signal
Graphic presentation of system operation
Solar pump speed control function
Control function of domestic water circulation pump or electric heater
Collector overheating protection function
Tank overheating protection function
Vacation function
Anti-freeze function
Counter of energy produced by the system
HYDRA GPS PWM electronic solar pump group with rotameter
Energy-saving electronic circulating pump Hydra GPS II 20-8-130 PWM2 Thermal insulation (housing)
Two ball check valves (integrated) with check valves and thermometer
Rotameter (2-12 l/min)
Safety group with pressure gauge and safety valve (6 bar)
Air separator
Installation fluid
The solar fluid is produced on the basis of propylene glycol, which means that it is completely safe for health in case of possible leakage into the domestic water. The fluid is hygienically certified by the National Institute of Hygiene, which is an additional guarantee of a high level of safety. The liquid is supplied in a 10-liter container in the form of a concentrate with a freezing point lower than -64 °C. After dilution with water, up to 30 l. of ready-to-use mixture is obtained, which is sufficient for typical installations.
Diaphragm vessel (expansion tank), solar 18 l.
Despite appearances, the diaphragm vessel is one of the most important components of a solar installation. The selection of a vessel with too low a permissible operating temperature or too low permissible pressure can cause frequent operating problems.
The maximum working temperature of the diaphragm vessel included in the kit is 120 °C, while the allowable working pressure is as high as 10 bar, which guarantees high stability of operation of the entire system.
Connection set
The kit is equipped with a system of brass compression fittings that allow efficient and secure connection of collectors with each other and connection with pipes.
The kit includes:
2 x Compression plugs for blinding two diagonal stubs of collectors
1 x Compression elbow with GZ ¾" connection for efficient connection to corrugated stainless steel pipes
1 x Crimp cross coupling with GZ ¾" connection enabling efficient connection with corrugated stainless steel pipes
REMARKS: In order to complete installation of the solar set, it is necessary to obtain, among others, a mounting kit for solar systems, solar piping and installation fittings necessary to connect the tank to the existing installation. The installation kit is not included as standard with ze
- Distribution class
- I
You might also like
201.60 zł (tax incl.)
Solar expansion vessel 18 l
514.50 zł (tax incl.)
WEBER SOL CLASSIC PWM solar controller
1,600.00 zł (tax incl.)
WEBER SOL ECO 2.8 solar collector
2,295.00 zł (tax incl.)