441.00 zł (tax incl.)
Solar set 1 x HP 30 vacuum tube collector with 200 l storage tank
Intended use: A solar kit with a hot water storage tank designed for single-family properties with daily hot water consumption not exceeding 150-200 liters, which usually corresponds to a family of 2-3 people.
POLAND PRODUCT
Solar set with 1 HP 30 vacuum tube solar collector + DHW cylinder. 200 l.
SOLAR KEYMARK certified to take advantage of subsidy programmes!
ESSENTIAL INFORMATION
High-quality solar set with a hot water tank. with a capacity of 200 litres and 1 HP 30 tube-vacuum solar collector included.
The assumed collector area provides efficient water heating of approximately 50% of the annual demand. The remaining 50% (winter period) should be provided by a central heating (central heating) boiler which is connected to the upper coil of the tank or by an electric heater.
COMPONENTS
1 x HP 30 vacuum tube solar collector
1 x WEBER W2 200 l dual-coil enamelled DHW cylinder
1 x WEBER CONTROL CLASSIC solar controller
1 x HYDRA GPS PWM electronic solar pump group with rotameter
1 x diaphragm vessel suspension
1 x solar expansion vessel (expansion tank) 18 l.
1 x propylene glycol, concentrate 10 l
1 x cross coupling fi 22 x 3/4"
1 x clamping elbow fi 22 x 3/4"
TECHNICAL SPECIFICATIONS OF MAIN COMPONENTS
HP 30 vacuum tube solar collector
Warranty: 6 years
Number of vacuum tubes: 30
Vacuum tube diameter: 58 mm
Glass tube wall thickness: 2 mm
Dimensions (W x L x H)" 245.5 x 199 x 18.2 cm
Total surface area: 4.89m²
Aperture area: 3,68 m²
Connection diameter: 22 mm
Optical efficiency (absorber / aperture): 93,7 % / 58,2 %
Heat loss a1 (absorber / aperture): 2.69/1.67 W/m2K
Heat loss a2 (absorber / aperture): 0.01 / 0.006 W/m2K2
Absorption: > 94 %
Emission: < 8 %
Weight of empty collector: 105.4 kg
Permissible installation angle: 15 - 50°
Housing colour: silver / black
Solar Keymark certificate
Storage tank
Warranty 4 years
Capacity: 200 l
Height: 130 cm
Diameter with insulation: 65 cm
Thickness of insulation: 5 cm
Number of coils: 2
Lower coil surface: 0.9 m2
Upper coil area: 0.6 m2
Maximum pressure: 10 bar
Corrosion protection: double enamel, magnesium anode
Casing: skay coat in grey or orange, depending on available batch
WEBER CONTROL CLASSIC controller
Large LCD display
Intuitive menu
Graphic display of system operation
Solar pump speed control function
Control function for domestic hot water circulation pump or electric heater
Collector overheating protection function
Storage tank overheating protection function
Holiday function
Anti-freeze function
Solar energy meter
Solar pump group HYDRA GPS PWM with rotameter
Energy-saving electronic circulating pump Hydra GPS II 20-8-130 PWM2
Thermal insulation (casing)
Two ball check valves (integrated) with non-return valves and thermometer
Rotameter (2-12 l/min)
Safety group with pressure gauge and safety valve (6 bar)
Air separator
Installation fluid
The solar fluid is manufactured on the basis of propylene glycol, which means that it is completely safe for health in the event of any possible leakage into the domestic water. The fluid is hygienically certified by the National Institute of Hygiene, which is an additional guarantee of a high level of safety. The fluid is supplied in a 10-litre container as a concentrate with a freezing point below -64 °C. When diluted with water, up to 30 litres of ready-to-use mixture is obtained, which is sufficient for typical installations.
Expansion vessel (expansion vessel), solar 18 l.
Despite appearances, the diaphragm vessel is one of the most important components of a solar installation. The selection of a vessel with too low an operating temperature or too low a permissible pressure can cause frequent operating problems.
The maximum operating temperature of the diaphragm vessel in the kit is 120 °C, and the permissible operating pressure is as much as 10 bar, which guarantees high stability of the entire system.
Fitting set
The set is equipped with a system of brass compression fittings enabling the collectors to be efficiently and securely connected with each other and with piping.
The set comprises:
1 x Compression elbow with ¾" GZ connection for efficient connection to stainless steel corrugated pipes
1 x Compression cross-piece with GZ ¾" connection enabling efficient connection to corrugated stainless steel pipes
REMARKS: For a complete installation of the solar set, you will need, among other things, a mounting kit for the collector, piping and installation fittings necessary to connect the tank to the existing installation. The mounting kit is not included as standard, due to the need to adapt it each time to the type of roofing and roof pitch. All these products can be purchased in our webshop.
ADVANTAGES
Low operating costs
Life in line with the ECO trend
Quick payback period
Fully maintenance-free
Long service life
- Distribution class
- H
You might also like
100.00 zł (tax incl.)
Propylene glycol, solar fluid -35°C, 5 l
2,522.00 zł (tax incl.)
Enamelled tank with 2 coils 200 l WEBER W2 200 tank boiler
201.60 zł (tax incl.)
Solar expansion vessel 18 l
3,200.00 zł (tax incl.)
HP 30 tube-vacuum solar collector
82.50 zł (tax incl.)